Altec Lansing computer speakers are a great investment. They can provide you with a sound that is crisp and clear, while also being easy to transport and store. Yet, sometimes they can be confusing to put back together.
When it comes time to take apart your computer speakers, here are some tips on how to do so:
Unplug the power cord from the electrical outlet
Disconnect all cables and wires that connect your speaker to your PC
Remove screws from the back of the speaker enclosure
Lay the speaker face down on a table or workbench so that you have access to the screws holding the top of speaker in place
Remove these screws using a Phillips screwdriver and gently pry off both pieces of the frame. Once removed, you should have access to all of the inner parts.
Ralated Article: 9 best computer speakers for music production in 2022
Why should you take apart your speakers?
You might wonder, why would you want to take apart your speakers? It’s a good idea to take apart your speakers every once in a while so you can clean them. Dust and dirt can collect on the inside over time, which can cause problems with sound quality. Taking your speakers apart will make it easier to get the dust out of them and put them back together.
If you’re looking for new speakers, take the opportunity when taking them apart to check out what strength of magnet they use or how many watts they output (see picture below). This way you’ll know what kind of power each speaker has before making a purchase decision.
How to take apart Altec Lansing computer speakers
Once you have the screws removed, your speaker should be easily taken apart. However, before you store your parts, remember to disconnect the wires and cables that connect it to your PC. Storing them without this step can result in a broken speaker.
If you’re looking for more tips on how to take apart Altec Lansing computer speakers, feel free to give us a call and we’ll be happy to provide you with more assistance!
How to put them back together
Putting the speaker back together is a lot easier than taking it apart.
– Lay the speaker on its face
– Line up the two pieces of the frame and gently snap them together
– Screw in all screws that were removed when taking the speaker apart
– Reconnect all cables and wires to their appropriate ports
– Plug in your power cord and test your speakers.
Why You Should Take Apart Altec Lansing Computer Speakers
Altec Lansing computer speakers are made to last. They can take a lot of abuse and still sound great. But if you’re looking for something new and you have some old speakers sitting around, why not put them to use? Taking apart Altec Lansing computer speakers is really quite easy. There are only a couple of screws in the back that need to be unscrewed, and then they come right apart! And once they’re apart, all sorts of new crafting possibilities open up. You could turn the pieces into an art project or maybe make an ornament out of it or just use it as the accent piece on your desk. There are so many ways you can use these old speakers. So don’t throw them away! Take them apart and make something new with them!
Tools Required to Take Apart Altec Lansing Computer Speakers
The tools required to take apart Altec Lansing computer speakers are:
– A Phillips head screwdriver
– A flathead screwdriver
– A pair of pliers
– Two pencils or chopsticks (to hold the speaker frame ends up)
Instructions on How to Take Apart Altec Lansing Computer Speakers
1) Remove the screws from the back of the speaker.
2) Gently pull apart the speakers to reveal the insides.
3) Cut any wires that are holding components together.
4) Separate all of the different parts and remove any screws or other hardware holding them in place.
5) Clean up all of the parts you removed and take a peek at what’s inside!
What to do with your old speakers
Before we begin, it’s important to make sure your speakers are not broken. If they’re working but just don’t fit in the space you need them to, then this guide is perfect for you. You can take apart your old speakers and make something new!
Take out all of the screws from the outside of the speaker cabinet. Generally there will be more than one screw on each side.
Once you have taken off all of the screws from the cabinet walls, gently pull them apart at a 45 degree angle with one hand. The other hand should be holding onto the front panel of the speaker, which will keep it from falling off.
The front panel is connected by a wire that runs down the middle of both sides and into the back of the cabinet. This wire needs to be removed before pulling apart any further.
Slide your fingers carefully around both wires and tug them out or cut them with scissors so that they are no longer attached to each side. Now you can remove them without being obstructed by anything else; simply lift up on either side and pull away from each other at a 45 degree angle as before.
Now you’re ready to take off any remaining screws on either side of the cabinet, starting with those on top—this is usually where there are more screws and they’re easier to access. Once these are removed, pull at an even 45 degree angle towards yourself and separate until you reach where they were originally screwed in on the bottom (they should
What are the different components of a computer speaker?
Inside the Altec Lansing computer speaker you will find:
– A woofer: This is one of two pieces that make up the subwoofer. The woofer has a cone and a spider, which is the component that moves in order to create the sound waves.
– A tweeter: This is an audio device that creates high frequencies and usually sits near the top of your speaker.
– Crossover: The crossover splits the signal from your computer so that it can be sent to both the tweeters and woofers.
– Amp: It converts audio signals into electronic signals for power amplifier stage or a preamplifier stage for powering loudspeakers.
– Power amp stage: This amplifies electronic signals in order to power loudspeakers.
– Preamplifier stage: This boosts low levels signals in order to increase their strength before they are converted into electronic signals for power amplifier stages or a crossover stage.
What is a computer speaker?
A computer speaker is a device that converts electrical audio signals into sound.
How to keep your speakers safe
Now that you’ve taken apart your speakers, here are some tips on how to put them back together. Make sure you line up the screws and holes before putting them back in place. This will help ensure that they go in straight and everything fits right. Once you have screwed the enclosure back in place, reconnect any cables or wires. Finally, plug your power cord back into the electrical outlet and make sure that it is securely connected to the speaker.
Various types of speakers
There are many types of speakers, but the most common ones that you will find in a computer lab are satellite and subwoofer speakers. The satellites are small and compact, while the subwoofers are large and have a deeper sound quality.
To take apart Altec Lansing satellite speakers:
– Unplug the power cord from the electrical outlet
– Disconnect all cables and wires that connect your speaker to your PC
– Remove screws from the back of the speaker enclosure
– Lay the speaker face down on a table or workbench so that you have access to the screws holding the top off both pieces of frame. Once removed, you should have access to all of the inner parts.
To take apart Altec Lansing subwoofer speakers:
– Unplug the power cord from the electrical outlet
– Disconnect all cables and wires that connect your speaker to your PC
– Remove screws from under speaker enclosure
– Lay speaker face down on a table or workbench so that you have access to screws holding top of speaker in place. Once removed, you should have access to all of inner parts.
Best computer speakers
for the money
As with any purchase, it’s important to invest in something that will last. You’re looking for computer speakers that will provide you with sound that is clear and crisp, while also being easy to transport and store.
You’ll be able to find these qualities in Altec Lansing computer speakers. They are a great investment because they will provide you with sound of the best quality, and are easy to store so you can take them on the go when needed.
FAQs
Altec Lansing computer speakers come in a variety of shapes and sizes. If you have the Altec Lansing Click Speaker, you might recognize it from its perforated grill design. But if you’re unsure how to find out what model of speaker you have, check the back of your speaker for a label with the model number. If there’s no label, then this guide probably won’t work for you!
How do I take apart my Altec Lansing speakers?
To take apart your Altec Lansing speakers, remove all of the screws holding the chassis to the base and carefully lift up the chassis. Take note of any cables connecting to other parts of your speakers as well so that you don’t accidently break them while dismantling. Once you’ve done that, it should be easy to see what parts can be reused and which ones need to go in the trash bin.
It’s easy! First, replace any damaged or missing parts, like the screws and brackets that hold the top frame in place. Then, reattach these pieces by screwing them back into place and reconnecting all cables and wires to your PC. Finally, restore power by plugging your speaker back into its electrical outlet and reconnecting any external cables or wires
Conclusion
Do you own a pair of Altec Lansing computer speakers? Then you may be wondering how to clean your speakers and keep them in the best possible condition. The answer is not as simple as it may seem. You might think that your speakers need only a quick wipe down with a damp cloth, but this will not remove the stains that have gathered in the speaker’s fabric grilles. To clean your speakers properly, you’ll need to take them apart and remove the grilles. Cleaning the fabric grilles is easy, but getting to the cloth that lines the speakers can be challenging. If you want to make sure your speakers are kept in optimal condition, follow these steps.
