How to wire a guitar blend pot

In this article, we will show you how to wire a guitar blend pot. You may be wondering why you would need to know how to wire a guitar blend pot. A lot of guitar players use this as a way to combine two different pickups and create different sounds.

For those who want more clarity on the subject, here is a step-by-step guide to wiring a guitar blend pot. Take off the knob and unscrew the top plate. Use the shortest length of guitar lead to connect both white wires together. Use another shorter length of lead to connect both black wires together. Connect one end of each coil with the corresponding hole for that coil. Screw on the top plate and replace the knob.

First things first, take your 4 inputs and plug them into the input jacks on the back of your guitar pot. Now take those inputs and plug them into the corresponding wires coming from the female jack on the other end of your wire nut. Twist both ends together as tightly as possible and put a little bit of electrical tape around them to make sure they stay tight as well as insulated from each other. Put electrical tape on any loose wires that are sticking out (for example, if you were using phone jacks). Then take your output jacks and plug them into the corresponding outputs on your guitar pot. You can now plug in your 6th input.

You look at our expert article on 10 Best Classical Guitars for the Money

What You’ll Need

– TRS Female Plug

– 1x Wire Nut

– 4x 1/4″ Phone Jacks or 1x 1/4″ Mono Male Plug

– Guitar Pot

What is a guitar blend pot?

A guitar blend pot is a device that is used to combine two pickups. A lot of guitar players use this as a way to combine two different pickups and create different sounds. For those who want more clarity on the subject, here is a step-by-step guide to wiring a guitar blend pot:

Step 1: Take off the knob and unscrew the top plate

Step 2: Use the shortest length of guitar lead to connect both white wires together. Use another shorter length of lead to connect both black wires together

Step 3: Connect one end of each coil with the corresponding hole for that coil

See also  Can you play the violin with short fingers

Step 4: Screw on the top plate and replace the knob.

How to wire a guitar blend pot

There are many ways to wire a guitar blend pot. The way it is done depends on the type of pot, the number of knobs, and the length of the lead you have.

If you are using a 3-knob guitar blend pot, then take off the knob and unscrew the top plate. Next, use the shortest length of guitar lead to connect both white wires together. Use another shorter length of lead to connect both black wires together. Connect one end of each coil with the corresponding hole for that coil. Screw on the top plate and replace the knob.

How does a guitar blend pot work?

A guitar blend pot is an incredibly helpful tool for guitar players. If you’re not sure what the term means, here’s an explanation. A blend pot is a variable resistor that allows two different pickups on a guitar to be blended together.

When you rotate the knob, one pickup will fade out while the other fades in. This allows you to create new sounds and tones with your guitar.

What are different types of guitars players use blends pots for?

Guitar players use blend pots for a variety of reasons. Some guitar players will put a blender pot between two different pickups to create a more unique sound. Others will use the blender to create a “kill” switch where they can turn off one pickup and let the other one be heard at all times.

Blend pots are also used by acoustic guitarists that want to get an electric sound with their instrument or vice versa (electric guitars that want to get an acoustic sound).

As you can see, there are many ways blend pots can be used, which is why it’s important for guitar players to know how to wire them correctly.

Wire the Inputs to the Outputs

So, to wire the guitar pot, take your outputs and plugs them into the input jacks on the back of your guitar pot. Now take those inputs and plug them into the corresponding wires coming from the female jack on the other end of your wire nut. Twist both ends together as tightly as possible and put a little bit of electrical tape around them to make sure they stay tight as well as insulated from each other. Put electrical tape on any loose wires that are sticking out (for example, if you were using phone jacks). Then take your output jacks and plug them into the corresponding outputs on your guitar pot. You can now plug in your 6th input.

See also  Why are bose speakers bad

Twist Together and Tape

Now, take those inputs and plug them into the corresponding wires coming from the female jack on the other end of your wire nut. Twist both ends together as tightly as possible and put a little bit of electrical tape around them to make sure they stay tight as well as insulated from each other. Put electrical tape on any loose wires that are sticking out (for example, if you were using phone jacks). Then take your output jacks and plug them into the corresponding outputs on your guitar pot. You can now plug in your 6th input.

Plug the Outputs Into the Inputs of Another Pot

Your guitar blend pot is now done. You can now plug your outputs into the inputs of another pot to make it more versatile or return them to their original positions for regular use.

Plug in Your 6th Input.

Plug in your 6th input to the output jack on your guitar pot. Twist the jack tightly into the hole and tape it down with electrical tape. You can now plug your guitar cables into these inputs.

Plugging in Your Guitar Cables.

Now take your guitar cables and plug them into your new wiring job. Simply push them in all the way until they are snug. If there are any loose wires you will want to secure them with electrical tape as well.

How to wire a guitar blend pot FAQS

What does a guitar blend pot do for my guitar?

A guitar blend pot is a type of potentiometer. A potentiometer can be used to control the volume output of an audio device, such as a guitar amp, and the volume output can be altered by turning the knob on the potentiometer (such as the one on your guitar’s volume knob). By wiring your guitar’s volume pots in parallel, you can create a blend between two different guitars plugged into separate inputs. This means that when you turn up one input and turn down another, they will both have an equal effect on the sound.

See also  How to glue guitar nut
Where should I place my 1/4″ phone jacks?

If you use 1/4″ phone jacks to wire your pot, place them at least 8 inches from each other or closer to each other if desired. You will need to slice through the outer casing of your plug with a utility knife and then strip back the wires inside so that they are exposed. Twist together all of your input wires coming from the female jack and then twist those into the corresponding output wires coming from your pot. Tape together any loose ends or exposed wire with electrical tape before continuing onto connecting your last input wire to its appropriate output wire.

Is it difficult to wire a guitar blend pot?

Wiring a guitar blend pot is not difficult as long as you have all of the necessary materials for doing so. One thing to note is that there are specific types of connectors for

Conclusion

So now you know how to wire a guitar blend pot.

But what do you do with it? The main use for a blend pot is to adjust the level of a pickup’s output relative to the other pickups in your guitar. In the below diagram, the 2nd input is wired to the 1st input to make it a “master volume” control.

This means that as you turn the 2nd input clockwise, you increase the level of both pickups at once. When it’s turned fully counter-clockwise, you get no sound from either pickup.

The 3rd input is wired to the 1st input to make it a “master volume” control as well, but with a twist. When it’s turned clockwise, you increase the level of both pickups at once – just like in the diagram above.

When you turn it counter-clockwise, you decrease the level of both pickups at once.

This means as you twist the 3rd pot counter-clockwise, as you turn the 3rd pot clockwise, or as you turn your guitar volume down or up, one pickup will always be louder than the other.