If you’re like me and are always messing around with your guitar, chances are that you’ve stripped the metal screw hole for one of the tuning pegs. Once this happens, it’s difficult to tune the guitar properly and play it like normal. However, how to fix stripped screw hole in guitar is discussed as below. Repairing a stripped screw hole in a guitar requires some patience and skill but is an achievable project for any guitar lover who likes to tinker around with their instrument. So grab your guitar, let’s get started.
Related Article: How to Fix A Stripped Guitar Strap Screw
Fixing a stripped screw hole in a guitar
First, you’ll need a drill with a metal bit to create a new hole. If you don’t have a metal bit, anything that is thin and pointy will work. The next step is to drill the new hole in the same place as the old one. You want to make sure it’s large enough for your screw so the head of the screw can go in without touching any of the wood inside. Next, insert your screw into the new hole and use a small amount of glue to secure it to the wood. This will hold your screw in place while you’re finishing up your project. Next, take some sandpaper and cut away any excess wood around the hole on both sides of it. Make sure you are cutting away from yourself so that you don’t accidentally cut yourself with sharp tools! The last step is to sand down any rough edges with sandpaper until everything feels smooth and fits snugly together.
What you’ll need
To fix a stripped screw hole in a guitar, you’ll need the following items.
-Cordless drill
-A piece of steel or brass bar (1/8”x1/2″)
-A heated coat hanger (optional)
-Some sort of bolt and nut to match up with the size of the stripped screw hole
-Wooden blocks
Removing the old pegs
The first step is to remove the old pegs from the guitar. To do this, use a drill or an electric screwdriver and carefully unscrew the two pegs.
The first step is to remove the old pegs from your guitar. This can be a little tricky, as you’ll need to slip off the old peg without ripping it off. For this step, you’ll want to use a small screwdriver and gently loosen the peg before pulling it out.
Next, take your drill with a metal bit on it and drill out the stripped screw hole. You’ll want to go all the way through the wood so that there’s enough room for your new screw to sit flush with the wood. Be careful when drilling so that you don’t drill into any strings!
After drilling out the hole, take your metal bit and make sure it’s still in place in front of the hole as well as against whatever material you’re using for filler. If necessary, use something like sandpaper to smooth down any rough edges until there are no jagged pieces sticking out that could hurt someone or damage equipment in storage.
Now it’s time for some filler! You can fill the hole with anything from wood putty or epoxy glue to super glue if you have enough patience (don’t worry about getting any on your strings). The key is finding filler that matches or compliments your guitar. Make sure that whatever filler you use doesn’t dry too quickly and mess up your work! Once dry, take some very fine-grit sandpaper and give it a few light strokes both ways just in case there are any bumps or uneven surfaces.
Removing the old screw
First, you’ll want to remove the old screw. You can do this by using a guitar pick, small flathead screwdriver, or other thin object to pry it out. If the screw is particularly stubborn, you may need something stronger like needle-nose pliers. Once you’ve removed the old screw, set it aside for now.
To start the process of fixing a stripped screw hole, you’ll want to remove the old screw.
There are two methods of removing screws from guitar tuning pegs: “unscrewing” or “cutting.” For this tutorial, we’re using the unscrewing method.
As you can see in the picture above, to unscrew a stripped screw all you need is a guitar tuner and something thin like a small flathead screwdriver. To begin, gently tap the wrench on top of the head of the screw to loosen it. Once it’s loosened, use your small flathead screwdriver to pry it out.
After you’ve successfully removed the old stripped screw from your tuning peg, take some wood glue or super glue and apply it to new metal screws before inserting them into your tuning peg holes. This will help prevent any further stripping for those specific tuning pegs in the future.
Cleaning your guitar
The first thing we need to do is clean the stripped screw hole. All sorts of gunk can get stuck in there, so it’s important to remove any debris that might have accumulated in the hole before you try and insert a new screw. You can use a rag for this task or even pour some rubbing alcohol down the hole.
Preparing to drill new holes
The first step in repairing a stripped screw hole is to drill new holes. Go ahead and locate the old screw hole, which should be near the center of the tuning peg. To find it, use a magnifying glass or jeweler’s loupe to scan the peg for a small circular depression. Drill two new holes with a drill bit that is about 1mm in diameter larger than the original screw screws. Make sure you are drilling at an angle away from the original hole.
Drill new holes with a drill bit
Once you’ve drilled the new holes, you will need to cut a piece of wood to fit the hole you just drilled. You can use any type of wood for this project and it’s best to use a piece that has been sanded down so that it is thinner than the original part of the guitar.
Then place the piece of wood over the stripped screw hole and drill it in with a drill bit slightly smaller than the screw you are using.
Once the new screw is in place, tighten it with your pliers until it’s snug but not too tight!
Drill new holes with a dremel tool
The first step to repairing your stripped screw hole is to drill new holes with a dremel tool. This should be done with a cutting disc and a grinding bit.
Installing the new screws and tuners
The first step is to drill out the stripped screw hole. You’ll need to drill a hole deep enough so that you can fit the new screws in. I recommend using a drill bit size that is slightly smaller than the size of your tuning pegs. For example, if the tuning peg is an inch long, use a 3/4″ drill bit. Once the hole is drilled out, take your new tuning pegs and screw them into place with your small screws. Make sure to tighten them securely but not too tight! Once you have completed installing all of your tuners, turn on your guitar and see if it sounds any better than before.
Reinstalling nuts, springs, and lubricant (optional)
If you’re having trouble installing the peg, use a small amount of lubricant on the threads before trying again. The lubricant will keep the threads from gripping to each other so that you can more easily get the peg in place.
When reinstalling nuts and springs, it is better to tighten them by hand first and then use the tuning key to tune them.
How to fix stripped screw hole in guitar FAQS
Repairing a stripped screw hole in a guitar requires some patience and skill but is an achievable project for any guitar lover who likes to tinker around with their instrument.
You will need a new peg, a large washer, drill bit and drill. If you don’t have these tools at home, you can find them at your local hardware store or on Amazon.
In order to successfully fix a stripped screwhole in a guitar, you’ll need to be patient and have some experience with small-scale repairs. If you are not familiar with doing this type of project, it will take some time for you to complete the repair.
To successfully fix the stripped screwhole in your guitar, you’ll need a guitar that has been disassembled, a drill bit that is just larger than the screw hole diameter (1/4 inch), and a 1/4 inch metal screw. You’ll also need a piece of wood or any hard surface on which to drill into.
Conclusion
If you find that your guitar has a stripped screw hole, don’t worry, there are a few ways to fix it.
In this article, you will learn how to drill new holes in the guitar and remove the old screw.
There are two different methods for drilling new holes in the guitar: using a drill and using a dremel tool.
Both tools work, but it is important to know the pros and cons of each.
Furthermore, this article will answer some frequently asked questions about stripped screw holes in guitars.
